Dr. Pen Official Store
Dr. Pen M7S Microneedling Pen
Dr. Pen M7S Microneedling Pen
Couldn't load pickup availability
Drpenofficial.store is an official Dr. Pen authorized retailer. Every Dr. Pen M7S purchased from our store is a genuine Dr. Pen device with authenticity verification. Designed for at-home microneedling on the face, neck and scalp, the M7S carries a quiet motor, six speed levels and a depth gauge running from 0 to 2.5 mm.
Quiet vertical needling, six speeds, and depth from 0 to 2.5 mm
The M7S drives its needles straight up and down, keeps depth and speed on separate controls, and runs from its own battery or from the cable.
- Six speed levels up to 16,000 rpm. A single button steps up through the levels and wraps back to the first, with the current setting held on the LED display.
- Depth from 0 to 2.5 mm. The dial on the body sets needle travel across the full range, turns independently of the speed button, and holds its position until it is changed again.
- Straight vertical travel. The needles move in and out rather than across the skin, which is what keeps a pass a clean channel instead of a drag and what keeps the motor quiet.
- Wireless or on the cord. Two to three hours of use from a full charge, with Type-C charging and a 2 metre cord for sessions that run longer than the battery.
- A low-battery warning with time to act on it. The display flashes once the charge falls to about 10 percent, which arrives before a pass rather than during one.
- A head that seats at three points. The connector holds the head square to the body instead of on a single mount, so it does not rock as the pen crosses a curved area; the 11-pin and 16-pin heads in this line run 0.18 mm needles.
- Heads across the range. The M7S shares its head line with the M8, covering the fine-gauge pin counts used for precise work and the nano heads used at the surface.
Who the M7S suits
The M7S is built for someone who wants the settings simple and the pen quiet in the hand. One button changes speed and one dial changes depth, and the two never interfere, so a session can be run without watching a screen. It suits a routine that runs on a schedule, because the gauge keeps its position between passes and the head mount keeps the head square without adjustment.
Complete Your Microneedling Setup
The head opens the channels; the serum decides what happens in them. A pure hyaluronic acid is the conventional base to work with, a skinbooster adds actives to that base, and a collagen serum is used over a longer course for firmness.
How to check your Dr. Pen M7S is genuine
Verification should cover the heads as well as the pen. Genuine Dr. Pen heads are sealed individually and carry a printed manufacturing date and expiry date; counterfeit heads arrive loose in unmarked packaging with no dates, and are the usual cause of irritation, uneven results and needles that drag rather than cut cleanly.
Every M7S we supply comes through the official Dr. Pen supply chain, and the checks you can carry out yourself are set out in how to verify your Dr. Pen. If the heads received do not appear correct, contact us before use.
❓ Frequently Asked Questions
How many speed settings does the M7S have, and when should they change?
Six. The single button on the front steps up through the levels and wraps back to the first, and the current setting stays on the display. Speed is a separate control from depth, so raising it changes how quickly a pass is completed rather than how deep the needles travel. Most routines settle on one or two levels and leave the depth dial to do the adjusting.
What is the three-point connection on the M7S head for?
It holds the head against the body at three points rather than on a single mount. That keeps the head square to the skin as the pen is moved across a curved area such as the jaw or the cheekbone, where a single mount can allow the head to rock and lift. A correctly seated head should take light pressure and stop positively. Fitting is walked through in how to use a Dr. Pen at home.
Can the M7S be used while it is charging?
Yes. The pen runs on the supplied Type-C cable and 2 metre cord as well as on the internal battery, so a session can be finished on the cable rather than stopped. Running on the cord does not change the depth or speed settings, and it does not interrupt a pass that is already under way.
How should the M7S be held and moved during a pass?
Hold it so the head sits flat against the skin and let the head do the work rather than pressing it in. Work small areas at a steady pace instead of sweeping across the whole face in one movement, and reload serum on each area before needling it. Keeping the pace and the pressure even across an area is what produces an even result.
Can the depth be changed part-way through an M7S session?
Yes. The dial turns independently of the speed button at any point, and the setting holds until it is moved again. That allows one session to stay shallow around the eyes and go deeper across the cheek. Any change in depth should be made before a pass begins rather than while the head is on the skin.
How often can I use the Dr. Pen M7S?
Once every three to four weeks. The change being aimed for comes from the skin rebuilding after a session, and that rebuilding takes weeks, so sessions run closer together interrupt the process instead of adding to it. Allow redness to clear completely before the next one, and fit a new head each time rather than reusing one. The full sequence is set out in how to use a Dr. Pen at home.
